Zeehaen - 1:37.5 - From Dutch Explorer Abel J. Tasman

Discussie in 'Bouwverslagen historische schepen' gestart door Marcus Botanicus, 22 mrt 2020.

  1. Hoosterw

    Hoosterw

    Lid geworden:
    22 jun 2011
    Berichten:
    2.920
    Locatie:
    Nuenen
    Scarfs in het Engels geloof ik.
     
  2. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    I don't have any aluminum, just brass and copper.

    I knew that when I asked about another word for butts, I was going to get comments such as yours.

    Hoosterw,
    You're corrects about the definition, callex scarf joi ts.
    Marcus
     
    Stephan Kertész vindt dit leuk.
  3. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Worked on the bow most of the day. Figuring and creating a bowsprite holder.

    [​IMG]

    Strengthening the deck.

    [​IMG]

    Glued deck in place.

    [​IMG]

    Used card to make a template of where the bowsprite goes.

    [​IMG]

    [​IMG]

    With a hand drill, drilled a hole through the bowsprite, deck and part of the wood. The drill bit kept it all in place while i could draw the lines for the holder.

    The area where the bowsprite goes into the ship, is there a name for that area?

    [​IMG]

    Bowsprite holder.

    [​IMG]

    [​IMG]

    Dry fit planking and bowsprite.

    Once i have planked that area and made a hole in it, I can slide the bowsprite with some glue into the holder.

    Marcus
     
    Jaques, janzwart, Pingu57 en 2 anderen vinden dit leuk.
  4. Pingu57

    Pingu57 Forum veteraan

    Lid geworden:
    14 dec 2014
    Berichten:
    8.176
    Locatie:
    Leeuwarden
    Marcus, het kleine dekje waar je boegspriet doorheen gaat om in het schip te komen is de "Luizenplecht "
    het gaat de goede kant op met je schip, mooi hoor :thumbsup::thumbsup:
     
    Marcus Botanicus vindt dit leuk.
  5. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Pingu,
    Thanks for the definition.
    In general this is one of the things I like about this site. Everyone takes the time to tell me what the Dutch definitions are for parts of a ship.
    Marcus
     
    Pingu57 vindt dit leuk.
  6. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Thank you for all the likes.

    Finishing up on the location of where the bowsprite goes into its holder and the little deck located at the tip of the stem.

    [​IMG]

    [​IMG]

    Started working on the bowsprite panel. Cut a piece of veneer by 0.5mm wider than the actual location of the panel so it is both a tight fit and slightly bowed or curved. Started paneling the veneer with 5mm wide cherry strips.

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    I still need to raise the wall from hull by 4mm. So then it is even with the other side.

    [​IMG]

    Bowsprite panel can be removed for easy adding 2 cathead squares, 1 gunprt and 3 steps.

    Once the glue dried the paneling was marked for the catheads and gunport.

    [​IMG]

    [​IMG]

    Gunport has been cut out. Tomorrow the 2 cathead squares will be removed.

    Marcus
     
    Laatst bewerkt: 23 apr 2020
    Jaques, janzwart, Hoosterw en 2 anderen vinden dit leuk.
  7. Pingu57

    Pingu57 Forum veteraan

    Lid geworden:
    14 dec 2014
    Berichten:
    8.176
    Locatie:
    Leeuwarden
    mooie vorderingen Marcus, dit heb je mooi opgelost met je boegspriet:)
     
    Marcus Botanicus vindt dit leuk.
  8. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Thank you for all the likes.

    Preparing the second layer of cherry planking. Most of the planks will be 20 cm long with a Dutch scarph joint on each side. There will also be smaller lengths.

    Put the planks in some water as they will cut better without splitting. Once the scarphs are cut the planks will be dried.

    [​IMG]

    Top plank is to show what the scarphs look like when cut.
    Middle plank is to show when the scarphs are together.
    Bottom plank being cut to make a scarph.

    [​IMG]

    Close up from a scarph being created.

    [​IMG]

    I will be creating joints on about 80 planks. Not all joints will be created now, some will be made when I plank the ship.

    Marcus
     
    Jaques, pietsan, Pingu57 en 3 anderen vinden dit leuk.
  9. Pingu57

    Pingu57 Forum veteraan

    Lid geworden:
    14 dec 2014
    Berichten:
    8.176
    Locatie:
    Leeuwarden
    Die aanhechtingen zien er zo goed uit Marcus, ik hoop dat je ze ook zo goed op het schip krijgt, dan zal denk ik nog best wel wat correctie nodig zijn, in verband met de verjonging van de planken die je straks nodig bent
     
    Marcus Botanicus vindt dit leuk.
  10. amazone

    amazone

    Lid geworden:
    3 aug 2009
    Berichten:
    2.445
    Locatie:
    vosselaar
    de lange lip las is wel mooi gemaakt ik heb het ook al eens proberen te maken maar ben er nog niet in gelukt ik zaag of snij ze nog altijd 1 voor 1 uit
     
    Marcus Botanicus vindt dit leuk.
  11. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    #Peter,
    Ik weet wel zeker dat ik elke plank een correctie moet geven als ik de lijnen van het schip volg.


    #amazone,
    Dat is aardig wat werk. Dat heb ik gedaan op de Boyer. Ik legde de plank einden op elkaar op de romp en met mes en lineaal de lippen maken.
    Marcus
     
    Pingu57 vindt dit leuk.
  12. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Thanks for all the comments and likes.

    I could not wait till Monday so I did a strake next to the keel. Started with a straight butt beginning at the lowest wale and continued with the Dutch scarphs. Used 4 pieces of 20cm long cherry planks and a little piece to finish the strake.

    [​IMG]

    Creating joints when the wood is wet, let the planks completely dry and then glue them together on the hull works well.

    Marcus
     
  13. Stephan Kertész

    Stephan Kertész

    Lid geworden:
    5 jul 2019
    Berichten:
    7.748
    Locatie:
    Ittervoort
    Nou ben benieuwd.
     
    Marcus Botanicus vindt dit leuk.
  14. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    This is what Ab Hoving said.

    Marcus
    Don't you think it would be wise to mark the lines of the bottom, the bilges and the lower wale on the hull before applying any strakes? That way you can monitor the various widths of the planking to avoid nasty corrections higher up the hull.
    The bottom is roughly 2/3 of the total width, the top of the bilges were mostly reached with three (sometimes 4) strakes. The position of the lower wale is there already, but has to be fine-tuned to ensure a fluent line. This is essential!
    Ab

    Ik doe nooit wat Ab zegt. Ik gok alles en het lukt aardig en dat is te zien aan mijn Boyer. Alle lijnen lopen mooi. Ik weet wel hoe het moet en heb het vroeger met een boot gedaan, daarna niet meer.

    Misschien is het beter dat ik het meet een fluit doe vanwege dat alle planken rara bochten maken.
    Niks bouwen en de boeken erbij.
    Marcus
     
  15. *Hans*

    *Hans* Vriend van modelbouwforum.nl Forum veteraan

    Lid geworden:
    30 okt 2012
    Berichten:
    6.771
    Locatie:
    Dordrecht
    Je lijkt wel een 17e eeuwse bouwmeester....:p
     
    Marcus Botanicus vindt dit leuk.
  16. Marcus Botanicus

    Marcus Botanicus

    Lid geworden:
    20 mrt 2015
    Berichten:
    790
    Locatie:
    Crown Point, IN, USA
    Is there a site or book that has the translation in Du - En and En - Du of ship words. When I read the different builds on this site there are many words I have to look up either in my van Dale (I have both books) or google translate.
    Thanks
    Marcus
     
  17. *Hans*

    *Hans* Vriend van modelbouwforum.nl Forum veteraan

    Lid geworden:
    30 okt 2012
    Berichten:
    6.771
    Locatie:
    Dordrecht
    Marcus,

    Ik heb de Engelse versie en de Nederlandse versie van Zu Mondfeld Historic Ship Models als pdf.
    Toesturen via WeTransfer?

    Hans
     
  18. JanZMC

    JanZMC

    Lid geworden:
    6 jan 2007
    Berichten:
    2.120
    Locatie:
    Roosendaal
    Heb nog ergens een document met de meeste termen in NL-EN-IT en volgens mij ook Frans. Moet wel ff goed gaan zoeken en dan omzetten naar pdf
     
  19. Stephan Kertész

    Stephan Kertész

    Lid geworden:
    5 jul 2019
    Berichten:
    7.748
    Locatie:
    Ittervoort
    Laatst bewerkt: 3 mei 2020
  20. Hoosterw

    Hoosterw

    Lid geworden:
    22 jun 2011
    Berichten:
    2.920
    Locatie:
    Nuenen
    Dat zou mooi zijn.
     
    Marcus Botanicus vindt dit leuk.

Deel Deze Pagina